Showing posts with label make it: candles. Show all posts
Showing posts with label make it: candles. Show all posts

Thursday, February 26, 2009

Make it: 1$ Store Candle Revamp

Make it: 1$ Store Candle Revamp
Cha-Cha-Cha Candles are so easy to whip up, all you need is a little Mod Podge and some images.

Materials:
Mod Podge - matte
tall glass candle
fun image
foam brush
glitter glue
ribbon
tacky glue
coil bracelet blanks
round-nose pliers
miscellaneous beads and baubles

1. Trim and/or resize the image to fit on the candle. Use a foam brush to coat the back of the image with Mod Podge. Apply the image to the candle, smoothing out air bubbles as you work.

2. Use glitter glue to highlight areas of interest on the image. Jewel glue can be used to apply sequins or rhinestones to a candle. Glue ribbon around the top and/or bottom of the candle with tacky glue.

3. Use round-nose pliers to create a small loop at one end of the bracelet coil; thread beads and baubles onto the coil, leaving enough space at the end to form another loop.

4. When the glue is dry, slip the beaded coil over the candle. The coil can be reused on other candles or worn as a bracelet.

Friday, November 14, 2008

make it: Copper Mesh Tea Lights


Copper Mesh Votive Holders

This mini craft can be whipped in just a few minutes. They look beautiful placed around a Thanksgiving table or across a mantel. The copper wire mesh is available at most craft stores and comes in a roll.

Materials:
copper wire mesh
work gloves
tin snips
24-gauge wire
wire cutters
round nose pliers
glass beads
small glass votive holder

Steps:
1. Cut a square of copper mesh about 6 inches on each side.

2. Center the votive holder on the wire mesh and fold the mesh up around the votive holder as desired. Press the mesh to crease it and hold the shape. Remove the votive holder.

3. Cut a long piece of wire and make a loop in one end. Thread one or two glass beds onto the wire and wrap the wire around the mesh several times, adding beads as desired. At the end of the wire, thread on one or two beads. Either tuck the excess wire into the mesh or make a loop to hold the beads and twist the two beaded ends together. Insert a tea light.

Thursday, November 13, 2008

make it: Orange & Clove Candle Holders

Orange & Clove Candle Holders
Supplies:
thick-skinned oranges or grapefruits
cloves
paring knife
mellon baller
metal tea light
1. Cut a hole in the fruit that's slightly larger than the diameter of the tea light. Use a knife to gently trace and carve out the area where the tea light will sit.
2. Use the melon baller to remove bits of fruit and create a well for the candle to sit.
3. Place a tea light in the well and press cloves into the skin to release the aromatic oils of the fruit and spice. If the fruit is thick-skinned, use a toothpick or a bamboo skewer to make the initial opening before inserting cloves.

Thursday, October 16, 2008

make it: Dollar Store Halloween Candles

Spooky Candles

You can easily trick-out dollar store candles with just a few simple supplies. They are prefect for lining a walkway on Halloween night!

Supplies:
Three tall glass enclosed candles
4” wooden letters, spelling “E-E-K,” or “B-O-O”
Craft paint
Paintbrushes
Perfect Pearls embellishing pigment kit—by Ranger Ink
Spray bottle filled with water
8 mm jump rings
E6000 glue
Chain
Needle-nosed jewelry pliers

Steps:

1. Paint the wooden letters with craft paint and allow them to dry. An eerie mix of green and black paint or a ghostly white work well.


2. Rub the pad of Pearlizing Perfect medium on each letter. Use a paintbrush to dust the patina powders included in the kit on each letter. Spray with water from the spray bottle to set the pigments, and allow them to dry.


3. Use E6000 glue to attach an 8 mm jump ring to the back of each letter in the center and at the top. Position the jump ring so that approximately half of the ring is exposed at the top of the letter. Allow the glue to dry for at least 8 hours.


4. Wrap chain around the lip of the candle glass. Link the chain together to form a loop of chain around the top of the candle with a tail of chain.


5. Use the needle-nosed pliers to attach another jump ring to the jump rings on the letters. Attach this second jump ring to the chain.

Tuesday, October 14, 2008

Make it: Tissue Transfered Candles

Tissue Transfered Candles

Transform plain candles with a few stamping supplies. Great for holiday gift giving and decorating! From the Medieval Lights episode of Creative Juice.

Supplies:
Light colored pillar candle
White tissue paper
Scissors
Rubber stamp
Ink pad – black
Purple embossing powder
Embossing gun
Luminarte Twinkling H2Os watercolors
Paintbrush
Parchment paper
Small scrap booking eyelets
Candle paint pen



1. Cut a piece of tissue paper that is large enough for your stamp. One side of the tissue paper will be slightly glossy. Ink your rubber stamp and stamp onto the glossy side of the tissue paper. If you’re using a larger stamp, place the inked stamp rubber side up on your work surface, lay the tissue paper on top of the stamp, and gently rub the paper to fully transfer the image. Gently lift the tissue paper from the stamp.


2. Sprinkle embossing powder on the image on the tissue paper and tap off the excess. Work over a manila file folder so that you can easily funnel excess embossing powder back into its jar. Heat the powder on the candle with an embossing gun until the image is embossed.


3. Swirl a wet paintbrush into the Twinkling H2O and color in the background of your stamp. (If you don’t have Twinkling H2O watercolors, any other type of watercolor will work.) Make sure your paintbrush is not too wet or your tissue paper may tear. Allow to dry (drying takes about ten to twenty minutes).


4. Cut a piece of parchment paper that is large enough to cover your image and wrap all the way around the candle, plus an extra several inches of length. Trim the excess tissue paper around the edges of your image. Place the image onto your candle. The embossed side of the image can face in toward the candle or outward, depending on your preferences. We placed the embossed side inward for a more antiqued look. Wrap the parchment paper tightly around the candle, using the excess parchment paper in the back as a handle.


5. Move your embossing gun over the image to melt the tissue paper into the candle. You will be able to see the wax melting through the parchment paper. Once you see the wax melt in one area, move the embossing gun to another area so as not to melt the candle too much. When the entire image has melted into the candle, carefully remove the parchment paper.



6. Add details to the candle using scrapbooking eyelets and candle paint pens. While the candle is still warm from step 5, press eyelets into the candle at the corners of the image. Add dots and lines with candle paint pens and allow the candle paint to dry for 24 hours.

enjoy!

Wednesday, July 16, 2008

Homemade Hardware on Creative Juice

Cathie Filian and Steve Piacenza
Homemade Hardware on Creative Juice

Tune in or Tivo
Thursday July 17th - 12:30 eastern DIY network




With the right parts and a little know-how, plain pipes are transformed into distinctive candleholders that will help light up any room.

Materials:
3/4" lead pipe, 6" long
3/4" lead flange
3/4" lead coupling
Sophisticated Finishes Patina Antiquing Set (includes copper metallic surfacer and patina green antiquing solution)
foam brush
acrylic primer

1. The flange will become the base of the candlestick. Screw one end of the pipe to the flange and the other end to the coupling.

2. Use a foam brush to apply a coat of primer to all surfaces and let dry.

3. With a small brush, apply copper metallic surfacer to the candlestick. Once dry, apply a second coat, but do not let this coat dry completely.

4. When the second coat becomes tacky, use a small paintbrush to apply patina green antiquing solution. Let the solution drip completely down the candlestick; wait a few minutes for the color to change.

5. Place a candle in the candlestick holder; if the candle is too loose, wrap its base with a small piece of aluminum foil to secure the fit.

Pipe-Part Candlesticks: Painted Finish Materials:
3/4" lead pipe, 6" long
3/4" lead flange
3/4" lead coupling
metal paint
foam brush
ribbon
hot glue

1. The flange will act as the base of the candlestick. Screw one end of the pipe to the flange and the other end to the coupling.

2. Using a foam brush, apply a coat of metal paint to all surfaces. Use a dry brush to feather the pipe, creating a distinctive textured look ,and let dry.

3. Apply a second coat of paint to the flange and coupling.

4. Embellish the top with a decorative ribbon; glue in place, folding back ends to prevent fraying.

5. Wedge a candle in the candlestick holder; if the candle is too loose, wrap the base with a small piece of aluminum foil to secure the fit.

________________________________



An ordinary metal washer becomes a funky piece of jewelry with nothing more than decorative paper and glaze.

Materials:
large washer
origami or other decorative paper
scissors
Quick Hold craft glue
Diamond Glaze from Judikins
pencil
1 yd. leather cording
leather clasp
flat-nose pliers
large hole punch

1. Make a laser-printer copy of the decorative paper; only a laser-printed image will work with this project, as a laser image will prevent the colors from bleeding when the diamond glaze is applied.

2. Trace the washer on laser-printed paper. Use a craft knife to cut out first the center, then the complete washer.

3. Place the washer smooth side down and glue paper to the rough side using Quick Hold craft glue.

4. Apply diamond glaze to the top of the washer; use a wooden skewer to spread the glaze, being careful to cover the entire surface of the washer. Let dry for 24 hours.

5. Cut lacing to desired length, fold in half, feed the folded end through the center of the washer and loop loose ends through the folded end.

6. Feed both ends of the cording through a bead, and slide bead down to the washer.

7. Trim ends of the lacing to fit your neck; attach a jewelry clasp to the ends using flat-nosed pliers.

________________________________



The '70s are making a comeback, and with this groovy storage locker decorated with lace trim, you’ll be packing in style.

Materials:
small footlocker
wide lace trim
thin rattail cord
tacky glue
scissors
dark red acrylic paint
acrylic primer
medium paintbrush
glazing medium
gold Rub N Buff

1. Tape off trunk hardware to protect from accidental paint drips.

2. In a bowl, mix white glue with water. Cut lace to fit edges, sides and top of trunk. Using a foam brush, apply glue directly to the trunk and attach lace.

3. Attach rattail cord to the trunk with glue mixture, creating decorative swirls, zigzags, patterns, etc. Use other pieces of lace to create flower shapes; just be sure to work on one side at a time (face up) and allow the strings to dry before moving to the next side.

4. Apply primer to entire trunk, making sure to really work the primer into the lace. Let dry overnight.

5. Apply red paint to the trunk; as with the primer, push the paint down into the lace and rattail cording. The process uses a large amount of paint, so make sure to allow a couple of days for the paint to dry.

6. Apply gold Rub N Buff to lace edges to bring out detail.

7. Remove the tape.

_______________________________



Tired of losing tools? Simple outlines on a pegboard will help keep crafting supplies organized and together in one place.

Materials:
appropriate size pegboard
tool hangers made for pegboard
spray paint (base color)
acrylic paint (accent color)
pencil

1. Paint base color on pegboard.

2. Hang tools on purchased hangers.

3. Outline tools with pencil.

4. Paint outline with acrylic accent color.

Monday, May 19, 2008

Get Glowing



Creative Juice - Episode #113 - Get Glowing

Tune in or TIVO - Tuesday on DIY Network - 12:30 eastern

Illuminating crafts are the order of the day as Cathie Filian and Steve Piacenza show you how to really let yourself glow. They turn old glasses into sparkling etched barware; transform plain glass jars into glowing container candles; and show you how to leave a secret glow-in-the-dark message for that someone special.


Friday, February 15, 2008

CHA Day 1 - luminary candle holder project




Vintage Vogue Luminaries


Supply List:
Mod Podge matte
glass cylinder vase
tape measure
color copy of image
scissors
foam paintbrush
wax paper
small glass votive
votive candle
optional: ribbon, rhinestones, silk flowers

Steps:

1. Measure the height and circumference of your vase, this will be the size of the collage you will need to create. Add an inch to the circumference.

2. Create a collage using wrapping paper, old greeting cards, clip art, scrapbook papers, stickers, etc. We used a vintage cover of a Vogue magazine and a graphic piece of scrapbook paper. Color copy the collage.

3. Trim the color copy to the appropriate size for your vase.

4. Working on wax paper, place the color copy printed side down. Using a foam brush apply a liberal coat of Mod Podge to the back of the paper, working quickly, flip over the paper and apply Mod Podge to the front of the paper.

5. Center the paper on the outside of the vase. Wrap around the vase, use your fingers to press out any air bubbles. Use your foam brush to smooth out your brush strokes.

6. Allow to dry for 24 hours.

7. Options: Add a thick ribbon around the base or top rim of the vase. Use a little hot glue to attach silk flower petals to the vase. Add extra bling by gluing rhinestones to the center of the flowers or in a random pattern around the luminary.

8. Drop a votive candle in the vase and watch it glow. (I like to use a small glass votive cup - it makes clean up a snap)






Tuesday, January 29, 2008

Creative Juice is Twice as Nice on Thursday

Tune in or Tivo to HGTV & DIY Network for Creative Juice!
We are Rockin Out with Rock projects and Stamping Up with cookie cutters.

Click here for all the project instructions: Rock Out Stamp Style

Modern Rock Art made with Mod Podge

Lovin' It
Desk Top Plants
Cocktails and Mocktails on the Rocks!
Homemade Stepping Stones
Strong!
Stamping UP!
Beeswax candles made with cookie cutters
Fabric printing with bleach and cookie cutters
stamped mailbox
Cleaning and caring for rubber stamps

Thursday, July 12, 2007

Soy Candle Project: from Living Live!




Create your own soy candles - it is easy & fun and soy wax burns cooler and cleaner than tradition waxes! So they last longer, are cleaner for the environment and great for people with allergies.

Ideas for containers: ramekins, sea shells, glass jars, tea tins, clay pot saucers, old glasses

Ideas for decorations: fringe trim, raffia, ribbons, scrapbook papers, sea shells, die cuts, stickers, paint pens

Supplies Needed:
soy container-blend wax
recycled glass jar
6 tsp. essential or fragrance oil
cotton-cored wick, 3" longer than the height of the container
metal wick base
candle thermometer
pencil
large glass measuring cup
large pan & stovetop or a microwave
oven mitts


Photo Sharing and Video Hosting at Photobucket

1. Determine the amount of wax needed by filling the glass container with water, pouring the water from the container into a measuring cup and making note of the amount. One pound of melted soy wax will make 2-1/4 c. liquid wax.


Photo Sharing and Video Hosting at Photobucket

2. Attach the metal wick base to one end of the wick, following instructions on the package. Tie the other end of the wick to the center of a pencil; balance the pencil across the opening of the glass jar (make sure the container is dry). The pencil will keep the wick straight during the pouring and cooling stages.


3. Stove Top Melting Method: Fill one-third of the pan with water and bring to a boil. Place unmelted wax in a glass measuring cup and sit the cup in the boiling water (this is a homemade double boiler).


4. Microwave Melting Method: Place desired amount of soy wax in a large glass measuring cup. Melt on medium temperate in short intervals. (1 minute at a time) The time it takes will depend on your microwave and the amount of wax you're melting.



Photo Sharing and Video Hosting at Photobucket

5. Place the thermometer in the wax and monitor the temperature, stirring as needed, until the melted wax has reached a temperature of 160 degrees (never heat above 160 degrees).


6. Wearing oven mitts, place the melted wax on a heatproof surface. Add fragrance oil after the temperature drops to 125 degrees; stir thoroughly. The intensity of fragrance is a personal preference: add more drops for a stronger scent. A good guideline is between 20 to 40 drops.


Photo Sharing and Video Hosting at Photobucket


Photo Sharing and Video Hosting at Photobucket

7. When the cooling wax reaches 110 degrees, pour it very slowly into a container to just below the rim. Check to make sure the wick is centered and taut before placing the container, away from cool and drafty places, to rest at room temperature.


8. When the wax is completely cool, trim the wick to 1/4" long. Wait four days before burning in order to settle the fragrance.


9. Add decorations or keep your design minimal. You can hot glue trim around the edge, add fun bits of paper to the glass with decoupage medium or tie a pretty ribbon around the edge.

 
Design by emfaruq. All Rights Reserved.